Chemical-Mechanical-Surface-Polishing-to-Improve-Mechanical-Performance-and-Corrosion-Resistance

Chemical-Mechanical Surface Polishing to Improve Mechanical Performance and Corrosion Resistance

The surface finishing process was performed by REM Surface Engineering, using their Extreme ISF Process®. This process combines a chemical polishing (CP) operation followed by a chemical mechanical polishing process (CMP). The CP was performed by immersion in a robot controlled chemical polishing bath. The CMP was performed in a 30 L circular vibratory bowl with a mix of non-abrasive ceramic media. The chemistry and dosing used for CP and CMP, as well as the media mix composition, shapes, and sizes, are the proprietary information of REM Surface Engineering and were not disclosed in the presentation.

Turning to the first of the case study examples, Fig. 2 shows the surface texture progression during the CP process of an PBF-LB (Ti-6Al-4V) specimen with porosity problems at the contour/hatching overlap region. It can be observed that most of the surface-related defects were remediated during the first 100 μm of surface metal removal (SMR) (Fig. 2, top right). The partially sintered/melted powder was eliminated and the surface profile peaks were partially planarised. Further processing eliminated most of the peaks. The deep valleys that were still present were significantly shallower and rounded, with a considerable planarisation level at 150 μm of SMR. At 175 μm of SMR, porosity associated with an unsuccessful overlap between the hatching pass and the contour was uncovered. This could usually be remediated with further processing at the expense of more sacrificial metal. This type of problem can be prevalent if extra care is not taken during the build process. Nevertheless, using a relatively inexpensive, fast, and easy CP process can check if some problems like this, or lack of fusion at the near-surface, occurred during the manufacturing process.

Fig 3

Fig. 3 Microscope images at 100 X magnification (a and b) with their 3D representations (c and d) of the surface of PBF-EB Ti-6Al-4V as-built tensile specimens, and the final surface after surface finishing (b and d). Average surface roughness (Ra) progression per surface material removal through the surface finishing operation (bottom). The blue area on the plot shows the CP progression and the red area shows the CMP progression [1]

The second part of the surface finishing process is the CMP, which involves using a specialised chemical formulation capable of producing a weak amorphous layer at the surface that is easily removed under minimal mechanical action, such as the media’s rubbing action in a standard vibratory bowl, accelerating the surface material removal rate. As a result, there is no need to use abrasive media that can be problematic in specific applications due to the possible introduction of inclusions into the sample’s surface and the risk of extra rounding on edges, delicate features, and corners. Fig. 3 shows the surface texture optimisation progression for PBF-EB Ti-6Al-4V specimens through the surface finishing operations. The as-built components showed typical surface texture features (Ra = 28 + 1 μm) that were eliminated through the CP process by removing 350 μm from the surface. The CP process reached a plateau and no significant change was observed upon further processing. At that point, the specimens were processed by CMP to achieve the required planarisation to target the required Ra. For the HCF (high-cycle fatigue) specimens built with contour and without contour, the Ra target was below 0.1!μm and Ra = 0.07 + 0.02 μm for the contour specimens and Ra = 0.06 + 0.01 μm for the specimens without contour were obtained with the same SMR of 487!μm. Both samples showed the same surface material rates and level of planarisation. Some random porosity was observed in both samples, even though they were HIPed, probably due to small spots lacking fusion, but these were sporadic.

Fig 4

Fig. 4 Average surface roughness (Ra) reduction per surface material removal through the surface finishing operation of PBF-LB GRCop-42, first CP followed by CMP (a). The blue area on the plot shows the CP progression, and the red area shows the CMP progression [1]

High-cycle fatigue testing was carried out on the PBF-EB Ti-6Al-4V specimens to study the difference between samples with and without a contour. The results showed that, at 275 MPa, both sets of specimens were stopped with no failure at 1,728,000 cycles, but, for the specimens run at 600 MPa, there was a significant difference in the cycles to failure between the contour specimens (Nf = 22,000 + 9,000 cycles) and the specimens without contour (Nf = 6,000 + 2,000 cycles). This demonstrated the importance of the contour process, where the contour specimens showed a higher fatigue lifetime, even though the contour layer served as a sacrificial layer during the 487 μm material removal.

The second case study focussed on PBF-LB GRCop-42 (Cu-4%Cr-2%Nb). GRCop-42 is a high-strength, dispersion-strengthened copper alloy with excellent conductivity, currently used in liquid rocket engines by NASA and other commercial space companies. Fig. 4 shows the surface texture progression for typical non-HIPed specimens of this alloy through the surface finishing operations. The as-built components show surface texture features overtaken by the partially sintered/melted powder on the surface, with Ra = (18 + 2) μm. The initial surface texture improved remarkably through the CP process; in this specific example, by removing around 200 μm from the surface, a Ra reduction of up to 78% was achieved; followed by the CMP process, reaching the lower possible Ra, where values under 0.6 μm were achieved (Fig. 4).

Finally, the PBF-LB IN625 case study was considered. The surface texture optimisation was performed by removing 400 μm from the surface by CP followed by 100 μm by CMP. The initial surface roughness of the as-built specimens was Ra = (8.3 + 0.5) μm and Ra = (7.5 + 0.2) for the HIPed samples. After applying CP + CMP, the final surface roughness was Ra = (1.1 + 0.6) μm for the non- HIPed samples and Ra = (0.07 + 0.01) μm for the HIPed samples. The non-HIPed sample surfaces showed significant shallow pits from the overall porosity, while the HIPed samples’ surfaces were perfectly smooth.

Fig 5

Fig. 5 Tensile strength (a), 0.2% yield strength (b), elongation (c), and uniaxial tensile high-cycle fatigue (Load at 434 MPa, room temperature, R = 0.1, and 60!Hz) of PBF-LB IN625 specimens before and after surface finishing and HIPing [1]

Fig. 5 shows the results of mechanical testing experiments performed on PBF-LB IN625 specimens. The tensile and yield strengths of the specimens were significantly reduced upon HIPing. Nonetheless, the surface finishing process increased these for both non-HIPed and HIPed samples and, in the case of the HIPed samples, the strength lost on HIPing was recovered. However, upon surface finishing, a significant decrease in elongation was observed. The observed effects on the tensile properties can also be associated with the residual compressive stress imparted to the material upon surface finishing. On the other hand, the effects of HIPing and surface finishing on fatigue properties were extremely significant, showcasing the importance of combining surface finishing and HIPing. Surface finished non-HIPed samples did not show a significant improvement in fatigue. The same was the case for HIP samples with no surface finishing. Influence of laser power on corrosion behaviour of PBF-LB Mg-Y-Nd-Zr alloy

 

Download Resource

Please fill out the information below to receive the selected resource.

Download Resource New Form

Please fill out the information below to receive the selected resource.

Hai domande?

Parla con un esperto