ISF Archives - REM Surface Engineering

Metal Finishing for 3D Printed Parts Webinar – Part 7 – OPEN IMPELLER

Posted by Danny Estrada on lunedì, Luglio 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

Metal Finishing for 3D Parts Webinar – Part 2

Posted by Danny Estrada on lunedì, Luglio 6th, 2020 in

What options are available? While many can be put into operation as sintered, there are a number of reasons – […]...

Metal Finishing for 3D Printed Parts Webinar – Part 1

Posted by Danny Estrada on lunedì, Luglio 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

Gear designers and manufacturers will need to review and update their tooth flank roughness specifications based on the new ISO 21920 GPS family of standards.

Changes Ahead in the Roughness Standards

Posted by Mark Michaud on lunedì, Giugno 22nd, 2020 in

Just when you thought it was safe to calculate a tooth flank surface roughness measurement, think again. By Mark Michaud […]...

Report of the Condition of a General Electric Transportation Systems Gearbox

Posted by Mark Michaud on martedì, Aprile 14th, 2020 in

Wind power plant operation and maintenance (O&M) costs remain an appreciable contributor to the overall cost of wind energy, with a capacity-weighted average of $11/megawatt-hour (MWh) for projects installed since 2000 and $9/MWh for projects install...

Rotorcraft Gearbox Regulations: LOL (not what you think)

Posted by Mark Michaud on lunedì, Marzo 16th, 2020 in

The European Union’s CS-29 Amendment 7 places more stringent and rigorous testing requirements for certification of Category A type pressurized gearboxes under loss of lubrication conditions compared to the previous regulation....

Roughness Measurement Tips: The Scratch Pad

Posted by Mark Michaud on giovedì, Gennaio 16th, 2020 in

You can check a profilometer’s overall performance following a quality-control-defined procedure and frequency using this traceable calibration specimen. By Mark Michaud […]...

A Comparison of Surface Roughness Measurement Methods for Gear Tooth Working Surfaces

Posted by Mark Michaud on venerdì, Ottobre 25th, 2019 in

A Comparison of Surface Roughness Measurement Methods for Gear Tooth Working Surfaces Matthew Wagner, Aaron Isaacson, Mark Michaud, and Matt […]...

Vibratory Media Compositions vs. Attrition and Density

Posted by Bill Nebiolo on martedì, Ottobre 1st, 2019 in

Vibratory media composition vs. attrition and density WILLIAM P. NEBIOLO PRODUCT MANAGER REM SURFACE ENGINEERING Media content is based […]...

Selecting media for optimum vibe bowl gear finishing

Posted by Bill Nebiolo on martedì, Agosto 20th, 2019 in

Selecting media for optimum vibe bowl gear finishing by WILLIAM P. NEBIOLO PRODUCT MANAGER Choosing the best media depends on […]...

How-to-set-up-a-vibratory-bowl-for-gear-finishing-07-19-MM

Materials Matter: How to Set Up a Vibratory Bowl for Gear Finishing

Posted by Bill Nebiolo on venerdì, Luglio 19th, 2019 in

How to Set Up a Vibratory Bowl for Gear Finishing William P. Nebiolo, REM Surface Engineering, Inc. Open or tight […]...

Physical Characteristics of the Vibratory Bowl and How They Affect Processing Efficiency

Posted by Bill Nebiolo on venerdì, Luglio 19th, 2019 in

Physical Characteristics of the Vibratory Bowl and How They Affect Processing Efficiency William P. Nebiolo, REM Chemicals, Inc., Southington, CT […]...